Fix wake-from-sleep, RAM overrun, and peripheral hangs in AVR firmware

Three defects prevented the board from working at all:

- INT0/INT1 were falling-edge triggered. Edge detection needs the I/O
  clock, which SLEEP_MODE_PWR_DOWN stops, so neither the reed switch nor
  the RTC alarm could wake the MCU. Both are now low-level triggered (the
  only asynchronous mode), and each handler masks its own interrupt while
  the source is still asserted so the low level cannot retrigger. The reed
  and RTC pins also get their pull-ups; they were explicitly driven low.

- Statics were 1440 B of 2048 with a 538 B main frame, so the first NFC
  read ran the stack into .data. Shrank the oversized buffers and made the
  NFC scratch buffer static: statics 1440 -> 1038 B, main frame -> 204 B.

- The FIFO was filled after entering TX mode with TxStart = FifoNotEmpty,
  so transmission began before the payload was loaded. Load in standby.

Memory safety: clamp the unvalidated RX length (len - 4 underflowed to
>=252 into a 60-byte buffer), fix writes one byte past DATA_BUFFER_65,
fix the diameter copy length in st25dv.c, NUL-terminate remove_spaces,
and bounds-check the NDEF parser (dropping its tag-sized VLA and its
unchecked payload_length decrements).

Hangs: add bail-outs to every peripheral poll loop - RFM69 mode/TX/RX
waits, the EEPROM WIP poll, all six I2C TWINT spins, and the ADC. The
LDO is cut before sleeping, so a slow peripheral hung the firmware with
no watchdog armed.

Correctness: boot no longer wipes the EEPROM spool; the replayed packet
is sent once and deleted only on success; short ATOMIC_BLOCK sections
replace the blanket cli() that lost reed pulses during the radio window;
the I2C rail comes up before the RTC is touched; sleep_bod_disable() moves
into the timed sequence with the sleep race closed; sei() no longer runs
inside ISRs; REG_FDEV_MSB was 0x06 twice so deviation was 0; ADC uses
return ADC and a /64 prescaler; SS1 is an output before SPE is set.

VAL_DATA_MODUL_OOK was misnamed rather than wrong - 0x01 lands in
ModulationShaping, not ModulationType - so the register value is
unchanged and on-air behavior still matches the base station.

Verified: builds clean under -Wall -Wextra on both gnu17 and c23.
Not yet run on hardware.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01YVJKatfeMJjAmuH9KYiLuv

avr_code/m95128.h

@@ -26,9 +26,12 @@
 #define EEPROM_RDLS 0b10000011 // 0x83
 #define EEPROM_LID 0b10000010 // 0x82
 #define PAGE_SIZE 64
+#define EEPROM_STATUS_WIP 0x01
+
+// A page write takes ~5 ms; past this the device is not responding.
+#define EEPROM_POLL_TIMEOUT_MS 100U
 #ifdef __cplusplus
 extern "C" {
-w
 #endif
 
     void
@@ -37,16 +40,16 @@ void eeprom_write(uint8_t page, unsigned const char* msg, uint8_t msg_len);
 void eeprom_read(uint8_t page, unsigned char* msg, uint8_t msg_len);
 void eeprom_write_tx_data(uint8_t page, tx_rx_data_struct tx_data);
 void write_page_address(uint8_t page);
-uint8_t get_last_page();
+uint8_t get_last_page(void);
 tx_rx_data_struct eeprom_read_tx_data(uint8_t page);
-void delete_last_page();
-uint8_t get_last_page();
+void delete_last_page(void);
+uint8_t get_last_page(void);
 void write_last_page_value(uint8_t page);
 void eeprom_clear_page(uint8_t page);
 void write_page_address(uint8_t page);
 void eeprom_write_tx_data(uint8_t page, tx_rx_data_struct tx_data);
 void write_struct_to_last_page(tx_rx_data_struct tx_data);
-tx_rx_data_struct read_struct_last_page();
+tx_rx_data_struct read_struct_last_page(void);
 #ifdef __cplusplus
 }
 #endif