Move pins files to subfolders #14573

Marlin/src/pins/stm32/pins_MALYAN_M200.h

@@ -0,0 +1,98 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * MALYAN M200 pin assignments
+ */
+
+#if !defined(__STM32F1__) && !defined(STM32F1xx) && !defined(STM32F0xx)
+  #error "Oops! You must be compiling for STM32."
+#endif
+
+#define BOARD_NAME "Malyan M200"
+
+// Enable EEPROM Emulation for this board
+// This setting should probably be in configuration.h
+// but it is literally the only board which uses it.
+#define FLASH_EEPROM_EMULATION
+
+#define SDSS SS_PIN
+
+// Based on PWM timer usage, we have to use these timers and soft PWM for the fans
+// On STM32F103:
+// PB3, PB6, PB7, and PB8 can be used with pwm, which rules out TIM2 and TIM4.
+// On STM32F070, 16 and 17 are in use, but 1 and 3 are available.
+#define STEP_TIMER 1
+#define TEMP_TIMER 3
+
+//
+// Limit Switches
+//
+#define X_MIN_PIN          PB4
+#define Y_MIN_PIN          PA15
+#define Z_MIN_PIN          PB5
+
+//
+// Steppers
+//
+// X & Y enable are the same
+#define X_STEP_PIN         PB14
+#define X_DIR_PIN          PB15
+#define X_ENABLE_PIN       PA8
+
+#define Y_STEP_PIN         PB12
+#define Y_DIR_PIN          PB13
+#define Y_ENABLE_PIN       PA8
+
+#define Z_STEP_PIN         PB10
+#define Z_DIR_PIN          PB2
+#define Z_ENABLE_PIN       PB11
+
+#define E0_STEP_PIN        PB0
+#define E0_DIR_PIN         PC13
+#define E0_ENABLE_PIN      PB1
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN         PA0   // Analog Input (HOTEND0 thermistor)
+#define TEMP_BED_PIN       PA1   // Analog Input (BED thermistor)
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN       PB6   // HOTEND0 MOSFET
+#define HEATER_BED_PIN     PB7   // BED MOSFET
+
+// FAN_PIN is commented out here because the M200 example
+// Configuration_adv.h does NOT override E0_AUTO_FAN_PIN.
+#ifndef FAN_PIN
+  //#define FAN_PIN        PB8   // FAN1 header on board - PRINT FAN
+#endif
+#define FAN1_PIN           PB3   // FAN2 header on board - CONTROLLER FAN
+#define FAN2_PIN           -1    // FAN3 header on board - EXTRUDER0 FAN
+
+// This board has only the controller fan and the extruder fan
+// If someone hacks to put a direct power fan on the controller, PB3 could
+// be used as a separate print cooling fan.
+#define ORIG_E0_AUTO_FAN_PIN PB8