thebears/marlin_skr
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

Bring configs up to date with 1.1.x

Browse Source
This commit is contained in:
Scott Lahteine
2017-12-30 20:05:43 -06:00
parent 7cc2193bce
commit 0b4a46fa6c
56 changed files with 241 additions and 220 deletions
Download Patch File Download Diff File Expand all files Collapse all files

31
Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
View File

@@ -638,7 +638,7 @@
* Z Servo Probe, such as an endstop switch on a rotating arm.
*/
#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector.
#define Z_SERVO_ANGLES {40,95} // Z Servo Deploy and Stow angles
#define Z_SERVO_ANGLES {40,85} // Z Servo Deploy and Stow angles
/**
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
@@ -786,17 +786,26 @@
// @section machine
// The size of the print bed
//#define X_BED_SIZE 207 // For now... use the old method of X_MIN_POS and X_MAX_POS to set X size
//#define Y_BED_SIZE 182 // For now... use the old method of Y_MIN_POS and Y_MAX_POS to set Y size
#define X_BED_SIZE 207
#define Y_BED_SIZE 182
// Travel limits (mm) after homing, corresponding to endstop positions.
#define X_MIN_POS 6
#define Y_MIN_POS 3
#define Z_MIN_POS 0
#define X_MAX_POS 207
#define Y_MAX_POS 182
#define X_MAX_POS X_BED_SIZE
#define Y_MAX_POS Y_BED_SIZE
#define Z_MAX_POS 175
/**
* Software Endstops
*
* - Prevent moves outside the set machine bounds.
* - Individual axes can be disabled, if desired.
* - X and Y only apply to Cartesian robots.
* - Use 'M211' to set software endstops on/off or report current state
*/
// If enabled, axes won't move below MIN_POS in response to movement commands.
//#define MIN_SOFTWARE_ENDSTOPS
#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
@@ -1718,9 +1727,9 @@
* LED Type. Enable only one of the following two options.
*
*/
//#define RGB_LED
//#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
#define RGB_LED_R_PIN 34
#define RGB_LED_G_PIN 43
@@ -1731,11 +1740,11 @@
// Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif
@@ -1766,16 +1775,16 @@
* Set this manually if there are extra servos needing manual control.
* Leave undefined or set to 0 to entirely disable the servo subsystem.
*/
#define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
#define NUM_SERVOS 2 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY { 500 }
#define SERVO_DELAY { 500, 500 }
// Servo deactivation
//
// With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE
#define DEACTIVATE_SERVOS_AFTER_MOVE
#endif // CONFIGURATION_H